can someone help me with a speed control sensor location?
Q. I have a 1997 Ford Contour. I was told that the speed control sensor was on the right side of the motor. Is that setting inside the car and looking at the passenger side or standing outside the car and looking at the driver side? I have looked ALL over the motor and cannot find it. Could someone PLEASE help me?
Asked by Jon - Thu May 13 22:26:27 2010 - - 4 Answers - 0 Comments
A. When talking right and left with cars it is always as if you were sitting in the driver compartment. The speed sensor is related to the transmission not the motor so you are looking in the wrong area. The speed sensor will be somewhere near the axle and reads a ring inside the transmission through magnetic interference. This can be on either side of the transmission and whoever told you where it was might know for sure but I do not. Hopefully I have been helpful though.
Answered by king_davis13 - Thu May 13 22:33:56 2010
Q. I have a 1997 Ford Contour. I was told that the speed control sensor was on the right side of the motor. Is that setting inside the car and looking at the passenger side or standing outside the car and looking at the driver side? I have looked ALL over the motor and cannot find it. Could someone PLEASE help me?
Asked by Jon - Thu May 13 22:26:27 2010 - - 4 Answers - 0 Comments
A. When talking right and left with cars it is always as if you were sitting in the driver compartment. The speed sensor is related to the transmission not the motor so you are looking in the wrong area. The speed sensor will be somewhere near the axle and reads a ring inside the transmission through magnetic interference. This can be on either side of the transmission and whoever told you where it was might know for sure but I do not. Hopefully I have been helpful though.
Answered by king_davis13 - Thu May 13 22:33:56 2010
where is the iat sensor location on 97 ford ranger?
Q. where is the iat sensor location on 97 ford ranger?
Asked by Ben M - Sat Jan 24 18:04:36 2009 - - 5 Answers - 0 Comments
A. From Haynes Repair Manual #36071: All Ranger 2.5L engines, 3.0L and 4.0L 1993 through 1999 and 2.3L engines 1993 through 1997 utilize an IAT sensor. Models following those years do not have an IAT sensor. If your Ranger falls in the category of having an IAT sensor, the sensor is located inside the air intake duct between the air cleaner housing and the throttle body. (the sensor electrical connector is likely visible from outside the air intake duct and the sensor fits into the duct and is removable from outside the air intake duct.)
Answered by Freddy Mac - Sat Jan 24 18:08:45 2009
Q. where is the iat sensor location on 97 ford ranger?
Asked by Ben M - Sat Jan 24 18:04:36 2009 - - 5 Answers - 0 Comments
A. From Haynes Repair Manual #36071: All Ranger 2.5L engines, 3.0L and 4.0L 1993 through 1999 and 2.3L engines 1993 through 1997 utilize an IAT sensor. Models following those years do not have an IAT sensor. If your Ranger falls in the category of having an IAT sensor, the sensor is located inside the air intake duct between the air cleaner housing and the throttle body. (the sensor electrical connector is likely visible from outside the air intake duct and the sensor fits into the duct and is removable from outside the air intake duct.)
Answered by Freddy Mac - Sat Jan 24 18:08:45 2009
does any one have a picture of a 2001 hyundai sonata vehicle speed sensor location?
Q. 2.4L 4cyl.
Asked by dream o - Mon Aug 27 10:45:57 2007 - - 1 Answers - 0 Comments
A. Hi, Please check on link. Hope this helps.
Answered by Trantanpla - Thu Aug 30 15:47:51 2007
Q. 2.4L 4cyl.
Asked by dream o - Mon Aug 27 10:45:57 2007 - - 1 Answers - 0 Comments
A. Hi, Please check on link. Hope this helps.
Answered by Trantanpla - Thu Aug 30 15:47:51 2007
toyota camry O2 Sensor LOCATION and HOW MANY are there?
Q. I wanted to know how many O2 sensors are in the 2001 Toyota Camry. I am having problems with it and the local shop told me to pay them $400.00 for them to replace it. I think it is an outrageous price for replacing an O2 sensor. I wanted to buy it on ebay or somewhere I can get it cheaper and install it myself. I always try to work on my cars, but this one I just can t figure out. Where are the O2 sensors located and also how many are there? Thanks. I did also call the dealer and it was even more expensive.
Asked by onelchris - Sat Feb 24 07:57:20 2007 - - 2 Answers - 1 Comments
A. Toyota uses "air/fuel ratio sensors" instead of O2 sensors sometimes and they are even more expensive than O2 sensors. Sometimes you end up stripping the threads getting the sensor out and you can get yourself into big trouble. So my advice is to simply continue to drive the car with the check engine light on as long as the car runs ok. Sometimes it's just the heater element that goes bad and the sensor works fine once the engine heats up. So you'll get a bad heater element error code but the sensor itself is still good once it gets hot.
Answered by bobweb - Sat Feb 24 08:11:53 2007
Q. I wanted to know how many O2 sensors are in the 2001 Toyota Camry. I am having problems with it and the local shop told me to pay them $400.00 for them to replace it. I think it is an outrageous price for replacing an O2 sensor. I wanted to buy it on ebay or somewhere I can get it cheaper and install it myself. I always try to work on my cars, but this one I just can t figure out. Where are the O2 sensors located and also how many are there? Thanks. I did also call the dealer and it was even more expensive.
Asked by onelchris - Sat Feb 24 07:57:20 2007 - - 2 Answers - 1 Comments
A. Toyota uses "air/fuel ratio sensors" instead of O2 sensors sometimes and they are even more expensive than O2 sensors. Sometimes you end up stripping the threads getting the sensor out and you can get yourself into big trouble. So my advice is to simply continue to drive the car with the check engine light on as long as the car runs ok. Sometimes it's just the heater element that goes bad and the sensor works fine once the engine heats up. So you'll get a bad heater element error code but the sensor itself is still good once it gets hot.
Answered by bobweb - Sat Feb 24 08:11:53 2007
92 Dodge Shadow Ambient Air Temperature Sensor Location?
Q. I have a 92 Dodge Shadow Turbo ES 2.5. My Ambient Air Temperature Sensor has gone bad i don't know where its at on my car does anyone know where its at so i can get it replaced?
Asked by LAW - Tue Feb 2 13:31:58 2010 - - 1 Answers - 0 Comments
A. It should be located in the front of the vehicle either between the grill and radiator or behind the bumper. If behind the bumper, you may have to raise the vehicle to locate it.
Answered by Frankie - Tue Feb 2 14:32:27 2010
Q. I have a 92 Dodge Shadow Turbo ES 2.5. My Ambient Air Temperature Sensor has gone bad i don't know where its at on my car does anyone know where its at so i can get it replaced?
Asked by LAW - Tue Feb 2 13:31:58 2010 - - 1 Answers - 0 Comments
A. It should be located in the front of the vehicle either between the grill and radiator or behind the bumper. If behind the bumper, you may have to raise the vehicle to locate it.
Answered by Frankie - Tue Feb 2 14:32:27 2010
Can someone please describe the location of the crankshaft position sensor on a 2003 Nissan Altima?
Q. I purchased the sensor after the OBD II equipment stated that there was a problem with it, and replaced a sensor that is exactly the same on the drivers side. I have a feeling that I got the camshaft sensor and not the one with the problem, therefore I need to know where the crankshaft sensor is so I can replace the right one. Dealership confirmed that the part number for both is the same but could not give me a diagram or help on the location... Thanks in advance! 2.5L engine Thanks to everyone that replied... I found and replaced the sensor. o Confirmed that camshaft & crankshaft position sensors are the same. o Crankshaft position sensor is a lot more difficult to replace as it is hidden under the engine and very difficult to access… [cont.]
Asked by Alfonso - Thu Aug 17 12:08:29 2006 - - 4 Answers - 0 Comments
A. Well do you have a 2.5 or 3.5 engine SE, LE, model They're on the right side of the engine when faceing the car need more detail info.
Answered by Puddin - Thu Aug 17 12:55:44 2006
Q. I purchased the sensor after the OBD II equipment stated that there was a problem with it, and replaced a sensor that is exactly the same on the drivers side. I have a feeling that I got the camshaft sensor and not the one with the problem, therefore I need to know where the crankshaft sensor is so I can replace the right one. Dealership confirmed that the part number for both is the same but could not give me a diagram or help on the location... Thanks in advance! 2.5L engine Thanks to everyone that replied... I found and replaced the sensor. o Confirmed that camshaft & crankshaft position sensors are the same. o Crankshaft position sensor is a lot more difficult to replace as it is hidden under the engine and very difficult to access… [cont.]
Asked by Alfonso - Thu Aug 17 12:08:29 2006 - - 4 Answers - 0 Comments
A. Well do you have a 2.5 or 3.5 engine SE, LE, model They're on the right side of the engine when faceing the car need more detail info.
Answered by Puddin - Thu Aug 17 12:55:44 2006
1998 olds aurora temp sensor location?
Q. It has enough coolant, but over heats going up hill. Computer says its a malfunctioning temperature sensor. Where is it located? Thanks for your help!
Asked by jmb162000 - Mon Feb 12 21:51:44 2007 - - 3 Answers - 0 Comments
A. what engine is in these car ? if norstar engine the sensor is on the lower head next to the fire wall 2 prong plug hope it helps
Answered by RAUL S - Mon Feb 12 23:07:53 2007
Q. It has enough coolant, but over heats going up hill. Computer says its a malfunctioning temperature sensor. Where is it located? Thanks for your help!
Asked by jmb162000 - Mon Feb 12 21:51:44 2007 - - 3 Answers - 0 Comments
A. what engine is in these car ? if norstar engine the sensor is on the lower head next to the fire wall 2 prong plug hope it helps
Answered by RAUL S - Mon Feb 12 23:07:53 2007
IAT intake air temperature sensor location 1997 Infiniti I30?
Q. there are several things plugged into whole air intake area. which of these is the IAT. also: autozone and other parts stores dont even carry them for this car. any suggestions?
Asked by lsn2npr - Sat Oct 6 14:47:47 2007 - - 1 Answers - 0 Comments
A. not 100% sure but check close to the egr valve and egr selonoid. you'll know it when you see it.
Answered by allen f - Sat Oct 6 14:56:39 2007
Q. there are several things plugged into whole air intake area. which of these is the IAT. also: autozone and other parts stores dont even carry them for this car. any suggestions?
Asked by lsn2npr - Sat Oct 6 14:47:47 2007 - - 1 Answers - 0 Comments
A. not 100% sure but check close to the egr valve and egr selonoid. you'll know it when you see it.
Answered by allen f - Sat Oct 6 14:56:39 2007
2005 Nissan Sentra Outside Air Temperature Sensor Location?
Q. My OAT is always reading around 90 - 100 when its actually 50 or below. Id like to check it for damage but am unable to locate it. Also my HVAC system (Heater) only blows heat when I am moving, when I stop at a light or idle it blows cold. Any correlation? Ive replaced my thermostat, and the inlet to my heater core is hot, What should I do?
Asked by Jason - Mon Nov 30 02:17:45 2009 - - 2 Answers - 0 Comments
A. Manual climate control or auto? rear View Mirror temp or elsewhere? Most times if properly installed the temp sensor is just ahead of the A/C condencer either fastened to the bumper cover or center hood latch reinforcement. Add on Mitto rear view mirror with temp compass the pick up may be placed whereever the installer wanted. Factory Pick up if disconnected and key turned on could display ICY for a couple days. Auto A/C temp sensor if unplugged A/C won't turn on until below 65 degrees
Answered by John Paul - Mon Nov 30 06:48:54 2009
Q. My OAT is always reading around 90 - 100 when its actually 50 or below. Id like to check it for damage but am unable to locate it. Also my HVAC system (Heater) only blows heat when I am moving, when I stop at a light or idle it blows cold. Any correlation? Ive replaced my thermostat, and the inlet to my heater core is hot, What should I do?
Asked by Jason - Mon Nov 30 02:17:45 2009 - - 2 Answers - 0 Comments
A. Manual climate control or auto? rear View Mirror temp or elsewhere? Most times if properly installed the temp sensor is just ahead of the A/C condencer either fastened to the bumper cover or center hood latch reinforcement. Add on Mitto rear view mirror with temp compass the pick up may be placed whereever the installer wanted. Factory Pick up if disconnected and key turned on could display ICY for a couple days. Auto A/C temp sensor if unplugged A/C won't turn on until below 65 degrees
Answered by John Paul - Mon Nov 30 06:48:54 2009
2001 toyota camry oxygen sensor bank 1 sensor 2 location?
Q. I need to replace my oxygen sensor in bank 1 sensor 2, but I have no idea where it is. I bought an oxygen sensor that is like the one for bank 1 sensor 1, will it work for sensor 2?
Asked by fried_noodles@sbcglobal.net - Mon Sep 28 22:00:08 2009 - - 1 Answers - 0 Comments
A. one sensor is located at the head of your car where the exhaust starts and the other is located before or after the catalytic converter, the one at the converter is #2, they are both the same
Answered by bigbadbear - Mon Sep 28 22:16:28 2009
Q. I need to replace my oxygen sensor in bank 1 sensor 2, but I have no idea where it is. I bought an oxygen sensor that is like the one for bank 1 sensor 1, will it work for sensor 2?
Asked by fried_noodles@sbcglobal.net - Mon Sep 28 22:00:08 2009 - - 1 Answers - 0 Comments
A. one sensor is located at the head of your car where the exhaust starts and the other is located before or after the catalytic converter, the one at the converter is #2, they are both the same
Answered by bigbadbear - Mon Sep 28 22:16:28 2009
1998 Pontiac Grand Prix Oxygen Sensor location?
Q. Where do I find the front oxygen sensor on a 1998 Pontiac Grand Prix? I can find the one on the backside of the engine but not the one in front. Any help would be great.
Asked by Mark S - Wed Nov 12 04:02:33 2008 - - 2 Answers - 0 Comments
A. On the rear side of the front manifold/pipe almost under the cover, see it from the bottom of vehicle.
Answered by Mike M - Wed Nov 12 04:28:41 2008
Q. Where do I find the front oxygen sensor on a 1998 Pontiac Grand Prix? I can find the one on the backside of the engine but not the one in front. Any help would be great.
Asked by Mark S - Wed Nov 12 04:02:33 2008 - - 2 Answers - 0 Comments
A. On the rear side of the front manifold/pipe almost under the cover, see it from the bottom of vehicle.
Answered by Mike M - Wed Nov 12 04:28:41 2008
99 Ford Explorer 4.0 Camshaft Position Sensor Location?
Q. My check engine light came on and i went to get a test to see what it was and it said camshaft position sensor location. How does this help my explorer? Also is it a major problems? ANd where is it located at? Correction: The test said there was something wrong with Camshaft Position Sensor not location.
Asked by gb298888 - Wed Oct 31 10:49:53 2007 - - 2 Answers - 0 Comments
A. Didn't say which 4.0 ..OHV or sohc ohv is in the back center of the engine and recommend a shop do it as usually if the sensor goes out, the piece it sits on has actually gone bad and destroyed the sensor (It's called a syncronizer and it has to be timed almost like a distributor) SOHC is on top the valve cover
Answered by gearbox - Wed Oct 31 23:33:13 2007
Q. My check engine light came on and i went to get a test to see what it was and it said camshaft position sensor location. How does this help my explorer? Also is it a major problems? ANd where is it located at? Correction: The test said there was something wrong with Camshaft Position Sensor not location.
Asked by gb298888 - Wed Oct 31 10:49:53 2007 - - 2 Answers - 0 Comments
A. Didn't say which 4.0 ..OHV or sohc ohv is in the back center of the engine and recommend a shop do it as usually if the sensor goes out, the piece it sits on has actually gone bad and destroyed the sensor (It's called a syncronizer and it has to be timed almost like a distributor) SOHC is on top the valve cover
Answered by gearbox - Wed Oct 31 23:33:13 2007
Nissan Sentra 2001 Oxygen sensor location? I have scanned my engine after Check engine soon po174 code?
Q. now there are 4 sensors with different wire colors,red,grey blue and black...which sensor I have to replace the scanner says bank 2. I want to use ,used sensor and they are asking me which wire color? can any body describe with sketch? Thank Mike,your ansewer is very detail but like to know what is the location of Long term fuel trims on both sides ,I have checked the response 800mv
Asked by shabbir s - Thu Jan 17 10:31:01 2008 - - 2 Answers - 0 Comments
A. You don't necessarily have a bad O2 sensor the code says that bank 2 is lean. You need to check Long term fuel trims on both sides and check the response of the O2 sensor by artificially enriching the fuel mixture and checking the voltage of the affected O2. It should achieve 800mv rapidly. You may have a vacuum leak. Nissan's are weird it could be a defective MAF sensor or dirty MAF sensor. Are you using a KN type air filter? that can have and affect because the oil from the filter coats the sense wire on the MAF and fools it to think less air is coming tin the engine than is, ergo lean. Usually when the sensor is bad, it sets a performance code slow response. in 12 years as drivability tech I don't think this code has ever set… [cont.]
Answered by Mike - Thu Jan 17 10:44:02 2008
Q. now there are 4 sensors with different wire colors,red,grey blue and black...which sensor I have to replace the scanner says bank 2. I want to use ,used sensor and they are asking me which wire color? can any body describe with sketch? Thank Mike,your ansewer is very detail but like to know what is the location of Long term fuel trims on both sides ,I have checked the response 800mv
Asked by shabbir s - Thu Jan 17 10:31:01 2008 - - 2 Answers - 0 Comments
A. You don't necessarily have a bad O2 sensor the code says that bank 2 is lean. You need to check Long term fuel trims on both sides and check the response of the O2 sensor by artificially enriching the fuel mixture and checking the voltage of the affected O2. It should achieve 800mv rapidly. You may have a vacuum leak. Nissan's are weird it could be a defective MAF sensor or dirty MAF sensor. Are you using a KN type air filter? that can have and affect because the oil from the filter coats the sense wire on the MAF and fools it to think less air is coming tin the engine than is, ergo lean. Usually when the sensor is bad, it sets a performance code slow response. in 12 years as drivability tech I don't think this code has ever set… [cont.]
Answered by Mike - Thu Jan 17 10:44:02 2008
Coolant Temp Sensor Location?
Q. Where can I find the coolant temp sensor for a 1995 Chevy Monte Carlo with the 3.4L engine? I need a picture or diagram or a VERY detailed description of where to find it. I have only had descriptions that state its on top of the intake manifold, but there is nothing there. Thank you in advance!
Asked by Soul Jah - Wed Feb 6 14:28:51 2008 - - 3 Answers - 0 Comments
A. Go to auto zone or a kragen etc. and they will show you.
Answered by gary o - Wed Feb 6 14:35:07 2008
Q. Where can I find the coolant temp sensor for a 1995 Chevy Monte Carlo with the 3.4L engine? I need a picture or diagram or a VERY detailed description of where to find it. I have only had descriptions that state its on top of the intake manifold, but there is nothing there. Thank you in advance!
Asked by Soul Jah - Wed Feb 6 14:28:51 2008 - - 3 Answers - 0 Comments
A. Go to auto zone or a kragen etc. and they will show you.
Answered by gary o - Wed Feb 6 14:35:07 2008
Coolant level sensor location - 1998 Chevy Malibu?
Q. Anyone know where the collant level sensor is located on a 1998 Chevy Malibu V6 3.1?? I already checked the owner's manual...
Asked by boobunny - Wed Nov 21 17:22:14 2007 - - 3 Answers - 1 Comments
A. It's on the bottom of the coolant bottle (the overflow). If your light is on and the coolant is full in the bottle take a small hammer and gently tap, have someone sit in the car with it running, and tap it until the light goes out, these sensors have a tendancy to get stuck and not operate properly.
Answered by Will S - Wed Nov 21 17:40:39 2007
Q. Anyone know where the collant level sensor is located on a 1998 Chevy Malibu V6 3.1?? I already checked the owner's manual...
Asked by boobunny - Wed Nov 21 17:22:14 2007 - - 3 Answers - 1 Comments
A. It's on the bottom of the coolant bottle (the overflow). If your light is on and the coolant is full in the bottle take a small hammer and gently tap, have someone sit in the car with it running, and tap it until the light goes out, these sensors have a tendancy to get stuck and not operate properly.
Answered by Will S - Wed Nov 21 17:40:39 2007
looking for a location to install a knock sensor on a ford 5.0?
Q. the vehicle is a 90 ford bronco fullsize it does require a knock sensor unfortunatly someone swapped the engine before i got the bronco. so original location in a bronco is non existant and being in the vehicle drilling and tapping the block is not an option. wondering if anyone has some ideas that have worked. or maybe drilling and tapping a hole into either the upper or lower intake plenum within reach of the wire harness? any good ideas are appreciated. i did notice an allen head plug on the drivers side of the block just above the oil pan fladge behind the exhuast manifold dead center inline with the last cylinder on that side just below where it angles up towards the head, but gotta get more propane for my torch before i can heat it… [cont.]
Asked by dj_lonewolf69 - Wed Apr 18 20:57:17 2007 - - 1 Answers - 0 Comments
A. I have had this problem before.Look around the engine block for any type of plug,maybe coolant passage plug.there is usually a plug on the side of the block and they are the same thread as the knock sensor.As long as its in the block,it should be fine
Answered by scott h - Wed Apr 18 21:23:16 2007
Q. the vehicle is a 90 ford bronco fullsize it does require a knock sensor unfortunatly someone swapped the engine before i got the bronco. so original location in a bronco is non existant and being in the vehicle drilling and tapping the block is not an option. wondering if anyone has some ideas that have worked. or maybe drilling and tapping a hole into either the upper or lower intake plenum within reach of the wire harness? any good ideas are appreciated. i did notice an allen head plug on the drivers side of the block just above the oil pan fladge behind the exhuast manifold dead center inline with the last cylinder on that side just below where it angles up towards the head, but gotta get more propane for my torch before i can heat it… [cont.]
Asked by dj_lonewolf69 - Wed Apr 18 20:57:17 2007 - - 1 Answers - 0 Comments
A. I have had this problem before.Look around the engine block for any type of plug,maybe coolant passage plug.there is usually a plug on the side of the block and they are the same thread as the knock sensor.As long as its in the block,it should be fine
Answered by scott h - Wed Apr 18 21:23:16 2007
Crankshaft Position Sensor Location?
Q. I am fixing my friends 2004 Audi A4 Quattro 1.8T Automatic. It sent code P0321 and P0322, which indicate bad Crankshaft Position Sensor. I need to know the location of the sensor. Thanks in advance.
Asked by Brandon - Mon Apr 5 02:30:37 2010 - - 2 Answers - 0 Comments
Q. I am fixing my friends 2004 Audi A4 Quattro 1.8T Automatic. It sent code P0321 and P0322, which indicate bad Crankshaft Position Sensor. I need to know the location of the sensor. Thanks in advance.
Asked by Brandon - Mon Apr 5 02:30:37 2010 - - 2 Answers - 0 Comments
thanks for the help still wandering about o2 sensor location?
Q. thanks for all the help about the vacuum lines i still need to know if i should change the top 2 o2 sensors or the bottom 2 . the car idles really rough in the morning especially when its cold it only lasts about 5 mins then evens itself out
Asked by Justin - Sat Dec 12 17:58:51 2009 - - 2 Answers - 0 Comments
A. It's NOT the o2 sensors. Don't waste your time and money. Fouled/damaged spark plug? Loose spark plug wire? ADDED: O2 Sensor? Probably NOT the problem. People like to blame the O2 sensor for the problem because that's where the computer fault appears. However, nine times out of ten, it's not faulty. It is simply reading a condition in the engine that is causing it to send a signal to the computer that there is a fault in the exhaust emissions mixture. A fouled spark plug, loose spark plug wire, a vacuum leak, dirty injectors, EGR valve, weak fuel pump, dirty fuel filter, weak ignition coil, plugged air filter, on and on, can all cause the O2 sensor to register a fault code. Before you yank the O2 sensor and replace it, check the basics… [cont.]
Answered by Mr. KnowItAll - Sat Dec 12 18:04:46 2009
Q. thanks for all the help about the vacuum lines i still need to know if i should change the top 2 o2 sensors or the bottom 2 . the car idles really rough in the morning especially when its cold it only lasts about 5 mins then evens itself out
Asked by Justin - Sat Dec 12 17:58:51 2009 - - 2 Answers - 0 Comments
A. It's NOT the o2 sensors. Don't waste your time and money. Fouled/damaged spark plug? Loose spark plug wire? ADDED: O2 Sensor? Probably NOT the problem. People like to blame the O2 sensor for the problem because that's where the computer fault appears. However, nine times out of ten, it's not faulty. It is simply reading a condition in the engine that is causing it to send a signal to the computer that there is a fault in the exhaust emissions mixture. A fouled spark plug, loose spark plug wire, a vacuum leak, dirty injectors, EGR valve, weak fuel pump, dirty fuel filter, weak ignition coil, plugged air filter, on and on, can all cause the O2 sensor to register a fault code. Before you yank the O2 sensor and replace it, check the basics… [cont.]
Answered by Mr. KnowItAll - Sat Dec 12 18:04:46 2009
where is the location of a knock sensor on a chevy blazer 2001?
Q. I had the blazer put on a machine...it showed the knock sensor is bad..however I can't find it to repair it...please help.
Asked by Carol H - Sat Jan 12 14:05:10 2008 - - 2 Answers - 0 Comments
A. The knock sensor is located Top rear of the engine, above the transmission bell housing, on the LH side ( right next to the distributor, below the oil pressure switch.) Now the bad news. The distributor needs to be removed, the oil pressure switch needs to be removed, to gain access to sensor.(sorry) It's a two wire connector A (dk blue ) knock sensor signal B (grey ) knock sensor return signal
Answered by jesse - Sat Jan 12 15:14:25 2008
Q. I had the blazer put on a machine...it showed the knock sensor is bad..however I can't find it to repair it...please help.
Asked by Carol H - Sat Jan 12 14:05:10 2008 - - 2 Answers - 0 Comments
A. The knock sensor is located Top rear of the engine, above the transmission bell housing, on the LH side ( right next to the distributor, below the oil pressure switch.) Now the bad news. The distributor needs to be removed, the oil pressure switch needs to be removed, to gain access to sensor.(sorry) It's a two wire connector A (dk blue ) knock sensor signal B (grey ) knock sensor return signal
Answered by jesse - Sat Jan 12 15:14:25 2008
Where is the location of front oxygen sensor for Honda Civic EX 99?
Q. I need to replace mine that's busted out. I searched online and people say it's pretty easy but I still need to find where the location is so that I can do it myself instead of paying $$$ to have repair shop do it for me.
Asked by Makan79 - Sat Nov 7 09:20:23 2009 - - 2 Answers - 0 Comments
A. It is probably mounted on the exhaust manifold in the front of the engine bay behind the radiator fans.
Answered by Andrew Y - Sat Nov 7 13:45:57 2009
Q. I need to replace mine that's busted out. I searched online and people say it's pretty easy but I still need to find where the location is so that I can do it myself instead of paying $$$ to have repair shop do it for me.
Asked by Makan79 - Sat Nov 7 09:20:23 2009 - - 2 Answers - 0 Comments
A. It is probably mounted on the exhaust manifold in the front of the engine bay behind the radiator fans.
Answered by Andrew Y - Sat Nov 7 13:45:57 2009
From Yahoo Answer Search: 'sensor location'
Fri Jul 9 04:16:55 2010 [ refresh local cache ]
[Hide]▼
newbeetle.org
TheBeetleLover
Mon, 24 May 2010 07:00:00 GM
Anyone knows which knock . sensor. is #2, driver or passenger? I've got P0332 knock . sensor. low input code and decided to replace it by myself. Dealer ask.
[Hide]▲
